| Load type and demand | Connected equipment, measured peak demand, motor starting, future additions, and load profile. | Separate continuous loads, intermittent loads, motors, HVAC, rectifiers, and other nonlinear loads. Use the expected maximum simultaneous demand rather than simply adding every nameplate rating. | Transformer capacity must support the actual operating load and its demand pattern without relying on unverified diversity or overload assumptions. |
| Required kVA rating | Real power in kW and the expected power factor, or the total apparent power in kVA. | For a three-phase load, calculate apparent power as kVA = kW ÷ power factor. Example: 400 kW at 0.90 power factor is about 444 kVA. With an illustrative 20% planning allowance, the result is about 533 kVA; a 630 kVA unit may be considered, subject to the load study and available ratings. | Transformer ratings are expressed in kVA. The planning allowance is an example, not a universal sizing rule; project-specific demand, ambient conditions, and future plans determine the appropriate margin. |
| Primary and secondary voltage | Utility supply voltage and the voltage required at the equipment terminals. | Document line-to-line voltage, frequency, allowable voltage variation, and any required taps. Common system examples include 400/230 V in many 50 Hz installations and 480/277 V in some 60 Hz installations; actual utility and site voltages vary. | A nominal-voltage match alone may not be sufficient. Confirm the utility connection, equipment ratings, tap range, and voltage-drop requirements with the project electrical design. |
| Frequency and supply conditions | System frequency, supply quality, switching events, and expected voltage fluctuations. | Specify 50 Hz or 60 Hz as applicable. Confirm suitability for the intended frequency and review unusual conditions such as frequent energization, significant voltage distortion, or operation outside the normal voltage range. | Frequency and supply conditions affect magnetic design, losses, heating, and compatibility. A transformer should not be assumed suitable for a different frequency without manufacturer confirmation. |
| Winding connection and vector group | Required primary and secondary connections, neutral availability, grounding method, and phase displacement. | Common arrangements include delta–wye with a grounded secondary neutral or delta–delta. Dyn11 is one commonly used vector group, but the correct choice depends on the system and must match connected equipment and any parallel units. | Connection and vector group influence grounding, neutral-current paths, phase displacement, and system compatibility. Confirm requirements with the utility and protection designer. |
| Impedance and fault level | Available fault current, required short-circuit performance, voltage regulation, and protection settings. | Obtain the transformer’s specified percent impedance and use it in the system fault-current study. Distribution transformer impedance values commonly fall in the approximate 4%–8% range, but the actual value depends on rating and design. | Impedance affects prospective fault current, voltage drop, and coordination of protective devices. Do not select it in isolation from the system study. |
| Load balance and neutral loading | Phase-by-phase load distribution, single-phase loads, neutral current, and unbalanced operating conditions. | Estimate phase loading and neutral current, especially where many single-phase or nonlinear loads are present. Plan for load balancing and specify any special neutral requirements. | Significant imbalance or neutral loading can increase losses and heating and may reduce usable capacity under the applicable design conditions. |
| Harmonics and nonlinear loads | Variable-frequency drives, UPS systems, data-center equipment, rectifiers, LED drivers, and other harmonic-producing loads. | Assess harmonic current and voltage distortion. If needed, specify a transformer designed for the harmonic duty and provide the applicable harmonic spectrum; a K-factor rating may be relevant in some specifications. | Harmonic currents can cause additional winding and structural heating. A K-factor designation does not, by itself, increase the transformer’s kVA rating. |
| Cooling and insulation | Indoor or outdoor location, fire and fluid requirements, ventilation, and maintenance preferences. | Common options include liquid-immersed, self-cooled units such as ONAN designs, and dry-type units using air cooling. Confirm enclosure, insulation, and cooling details for the installation environment. | Cooling method and insulation system affect installation constraints, service requirements, losses, and suitability for the site. Applicable fire and environmental rules may limit the options. |
| Ambient conditions and installation | Ambient temperature, altitude, moisture, dust, corrosive exposure, ventilation, seismic conditions, and available space. | Provide site temperature and altitude data, indoor/outdoor classification, enclosure needs, access clearances, and acoustic limits. Confirm whether any rating adjustments are required by the applicable design and standards. | Environmental conditions can affect cooling, insulation life, noise, and allowable loading. A standard rating should not be assumed to apply unchanged in every installation. |
| Efficiency and total cost | Expected loading over time, energy prices, operating hours, and applicable efficiency regulations. | Compare guaranteed no-load and load losses using the project’s expected load profile. Check the efficiency requirements that apply in the installation jurisdiction and procurement date. | Purchase price is only part of lifecycle cost. No-load losses occur whenever the unit is energized, while load losses vary with current. |
| Standards, testing, and documentation | Jurisdiction, utility specifications, required tests, certifications, and project documentation. | Specify the applicable standards and editions, such as the relevant IEC 60076 or IEEE C57 requirements, as adopted by local rules. Request a rating plate schedule, test reports, impedance data, loss guarantees, and connection diagram. | Requirements differ by region and project. Confirm the governing code, utility rules, and acceptance tests rather than relying on a generic specification. |